207w manual

These cookies do not store any personal information. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Privacy Overview This website uses cookies to improve your experience while you navigate through the website. Privacy Overview. Necessary Always Enabled. Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Axis W owners to properly answer your question.

View the manual for the Axis W here, for free. This manual comes under the category Security cameras and has been rated by 2 people with an average of a 8.

Power Supplies. Voltage: 5. Cables and connectors. Extension cable PS-H, 1. Pitch: 3. Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Check the package contents against the list below. Hardware overview. Familiarize yourself with the camera. See page 4. Install the hardware and make all cable connections. See page 7. Set an IP address. See page 8. Set the password. See page Configure the wireless connection. This product must be used in Adjust the focus. Camera stand Supplied with 3 mounting screws. The extension section is ready fitted.

The serial number may be required during the installation. Using shielded cables is recommended. Power connector - Mini DC connector.

If used with an external relay, a diode must be connected in parallel with the load, for protection against voltage transients. The AXIS has a different pinout and power - see the table above.

Green Steady for connection to a wireless network. Flashes for network activity. Red Steady for no wireless network connection. Flashes when scanning for wireless networks. Green Steady green for normal operation. Note: The Status LED can be configured to be unlit during normal operation, or to flash only when the camera is accessed.

See the online help files for more information. Amber Steady during startup, during reset to factory default or when restoring settings. Red Slow flash for failed upgrade. Green Normal operation. Install the hardware!

Damage as a result of exposure to strong light is not covered by the Axis warranty. Mount the camera Wall mounting 1. If required, use the 3 supplied screws to fix the base plate to a flat horizontal or vertical surface. To use a shorter stand, unscrew the lock ring to release the camera, and remove the extension section.

Attach the camera, adjust the angle and tighten the lock ring. Shelf mounting 1. Position the clamp and tighten the fixing screw securely. Attach the clamp to the lock ring on the camera. Adjust the angle and tighten the lock ring. Connect the cables 1. Using the self-adhesive strip, attach the supplied cable clip to the rear panel and fasten the power cable to it.

This will prevent accidental cable disconnection. Connect the camera to the network using a shielded network cable. Optionally connect external devices, e. See page 5 for information on the terminal connector pins. Check that the indicator LED:s indicate the correct conditions. See the table on page 6 for further details.

Note that some LED:s can be disabled and may be unlit. This number may be required during installation. Use the method that best suits your purpose. Both of these free applications are available on the Axis Network Video Product CD supplied with this product, or they can be downloaded from www.

The application can also be used to manually set a static IP address. When the camera appears in the window, double-click it to open its home page.

See page 12 for instructions on how to set the password. Set the IP address manually 1. Acquire an unused IP address on the same network segment your computer is connected to.

The serial number is located on the product label. Click the Set IP button and follow the instructions. Set the IP address for a single device 1. Check that the camera is connected to the network and that power has been applied. Select the devices you wish to configure different models can be selected and click the Assign IP button.

All methods are enabled by default, and all can be disabled. Navigate to the Bonjour bookmark in your browser e. See www. The command must be issued within 2 minutes of connecting power to the camera.

Acquire an IP address on the same network segment your computer is connected to. Click OK. Enter a password and then re-enter it, to confirm the spelling. Note: The default administrator user name root cannot be deleted. Enter the password as set above, and click OK. You will need administrator rights on the computer to do this.